Simultaneous improvement of corrosion and mechanical properties of AA 5083 aluminum alloy
In this study, the effects of cold-rolling and annealing on the structural, electrochemical, and mechanical properties of AA5083 in a simulated seawater environment are investigated. The results demonstrated that annealing temperature significantly affects the alloy's mechanical and corrosion properties. According to potentiodynamic results, the rate of corrosion decreased after annealing. Compared to the cold-rolled sample, the heat treatment doubles the electrochemical impedance, indicating that the corrosion resistance of AA5083 alloy is suitable at 50°C annealing. Approximately twice as much ductility was added to the materials as compared to the as-received materials. Additionally, the mechanical testing revealed the Portevin-Le Chatelier (PLC) Effect Type B band, which reflected the smaller grain size.
Robert J. Mills, Brian Y. Lattimer, Scott W. Case, Adrian P. Mouritz: Corrosion Science 143 (2018) 1-9
F.Gui: Novel corrosion schemes for the aerospace industry, Metals and Surface Engineering (2009) 248-265
H.M.M.A. Rashed, A.K.M. Bazlur Rashid: Comprehensive Materials Finishing, Elsevier, (2017) 337-371
V. N. Gaitonde et al: Journal of Minerals and Materials Characterization and Engineering, 11 (2012) 695-703
J. Kerry: Packaging Technology, Woodhead Publishing, (2012) 163-177
J.R. Davis: Corrosion of Aluminum and Aluminum Alloys, ASM International (1999)
E.L. Huskins, B. Cao, K.T. Ramesh: Materials Science and Engineering A, 527(6): (2010) 1292-1298
J. R. Davis and Associates: ASM Specialty Handbook: Aluminum and Aluminum Alloys ASM International, Materials Park, Ohio, 1994
F.S. Bovard: D.A. Shifler (Ed.), ECS Joint International Meeting, (2004) 232-243.
J.L. Searles, P.I. Gouma, and R.G. Buchheit: Metall. Mater. Trans. A 32 (2001) 2859
R. Goswami, et al: Mater. Sci. Eng., 527A (2010) 1089-1095
Ove Nese, Corrosion properties of AA5083 and AA6082 in seawater - effect of temperature, pH and potential (2016)
Petru Moldovan, Carmen Nicoleta Stanica, Gilbert Ciobanu, Ionel Ungureanu, George Manuel Iorga, Mihai Buţu: I U.P.B. Sci. Bull., Series B, Vol. 76 (3): (2014) 169-180
Zhang, R., Steiner, M.A., Agnew, S.R. et al.: Sci Rep. 7 (2017) 2961
Kiryl Yasaka, M.L. Zheludkevich, Sviatlana V. Lamak, Mario G S Ferreira: Electrochimica Acta 52(27): (2007) 7651-7659
S.O. Adeosun, O.I. Sekunowo, S.A. Balogun, and V.D. Obiekea: Int. J. Corros., 2012, 2012, p 1-9
In et al.: Materials Science and Technology 27 (4): (2011) 789-792
Aline Chemin, Denys Marques et al.: Materials and Design 53 (2014) 118-123
Hosni Ezuber, A. El-Houd, F. El-Shawesh: Materials and Design 29(4): (2008) 801-805
D. Singh et al.: International Journal of Minerals, Metallurgy and Materials 20 (8): (2013) 759
Wang Jinlian, Xu Jun, Pan Feng: Results in Physics 10 (2018) 476-480
P Nageswara Rao,D Singh &R Jayaganthan: Materials Science & Technology 29 (2013) 76-82
Cui Chang-hua, Gao Kun-yuan, Nie Zuo-ren, Wen Sheng-ping, Huang Hui: Corrosion & Protection 32 (2): (2011) 94 - 98
Chun-Hung Yen, Chih-Ting Wu, Yen-Hao Chen, Sheng-Long Lee: Journal of Materials Research 31(08): (2016) 1163-1170
Miljana Popovi, Endre Romhanji: Journal of Materials Processing Technology 125-126: (2002) 275-280
J. Gilbert Kaufman, Introduction to Aluminum Alloys and Tempers, ASM International, (2000) 39-76
Chuanjun Huang et al: 2017 IOP Conf. Ser.: Mater. Sci. Eng. 279 01(2002)
Snopiński P, Tański T, Gołombek K, Rusz S, Hilser O, Donič T, Nuckowski PM, Benedyk M.: Materials 13 (2): (2020) 301
Kalemba-Rec, M. Wróbel and M. Kopyściańsk: Acta Physica Polonica A 130 (2016) 996-999
Masahiko Morinaga: A Quantum Approach to Alloy Design (2019) 221-260
Adriana Valerio, Sergio L. Morelhao: Materials Science, 1(2019)
Malayathodi, Rijesh & Sreekanth, M.S. & Deepak, A. & Dev, K. & Surendranathan, A.O.: International Journal of Mechanical Engineering and Technology, 9 (2018) 646-652.
K. Mallaiya, R. Subramaniam, S.S. Srikandan, S. Gowri, N. Rajasekaran, A. Selvaraj: Electrochim Acta 56 (2011) 3857-3863.
Wang Jinlian, Xu Jun, Pan Feng: Results in Physics, 10 (2018) 476-480.
Juliana de Paula Martinsa, André Luis Moreira de Carvalhob, Angelo Fernando Padilhac: Materials Research, 15(2012) 97-102.
Zainuddin Sajuri, Nor Fazilah Mohamad Selamat, Amir Hossein Baghdadi, Armin Rajabi, Mohd Zaidi Omar, Amir Hossein Kokabi and Junaidi Syarif: Metals, 10(2020) 70.
Naik, S.N., Walley, S.M.: J Mater Sci, 55 (2020) 2661-2681.
D. A. Zhemchuzhnikova, Mikhail Lebyodkin, Tatiana Lebedkina, R. O. Kaibyshev: A, Elsevier, 639 (2015) 37-41.
Ni Tian, Guangdong Wang, Yiran Zhou, Kun Liu, Gang Zhao & Liang Zuo: Materials, 11(2018) 1533.
M. N. James: Engineering Failure Analysis, 18 (2011) 1909-1920.
Zhu, Z., Jiang, X., Wei, G. et al. Acta Metallurgica Sinica (English Letters), 33 (2020) 1369-1378.
U. Donatus1, G. E. Thompson, J. A. Omotoyinbo, K. K. Alaneme, S. Aribo, O. G. Agbabiaka: Trans. Nonferrous Met. Soc. China, 27 (2017) 55-62.
Xinxin Zhang, Xiaorong Zhou, Teruo Hashimoto, Bing Liu: Materials Characterization, 130 (2017) 230-236.
Newman R.: Journal of Corrosion Science, 37 (1995) 527-533.
Cai D, Han S, Zheng S, Luo Z, Zhang Y, Wang K, Journal of Materials Processing Technology, 255 (2010) 530-535.
How to Cite
Copyright (c) 2022 Qanita Tayyaba, Adnan Qayyum Butt, Muhammad Shahzad, Tahir Ali
This work is licensed under a Creative Commons Attribution 4.0 International License.
Authors who publish with this journal agree to the following terms:
- Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgment of the work's authorship and initial publication in this journal.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgment of its initial publication in this journal.
- Authors are permitted and encouraged to post their published articles online (e.g., in institutional repositories or on their website, social networks like ResearchGate or Academia), as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).
Except where otherwise noted, the content on this site is licensed under a Creative Commons Attribution 4.0 International License.