Micromechanical modelling of ductile fracture - local approach
DOI:
https://doi.org/10.30544/459Keywords:
Welded joints, Ductile fracture, Micromechanical modeling, local approachAbstract
Micromechanical modelling of ductile fracture by using the local approach has been presented as the review of previously obtained results for welded joints made of low alloyed high strength steel. Experimental work was performed on 3PB specimens and tensile panels, which were then modelled by finite element method, using two- and three-dimensional meshes, respectively. The local approach was used to simulate both for crack initiation and growth during ductile fracture process.
References
F.M. Beremin: Met Trans, 14A (1983) 2277-2287.
M. Rakin, Z. Cvijovic, V. Grabulov, S. Putic, A. Sedmak: Engineering Fracture Mechanics, 71 (2004) 813-827.
M. Rakin, N. Gubeljak, M. Dobrojević, A. Sedmak: Engineering Fracture Mechanics, 75 (2008) 3499-3510.
M. Rakin M, Numerical analysis in local approach, In: Experimental and numerical methods of fracture mechanics in structural integrity assessment, Sedmak S. and Sedmak A. (Eds.), TMF-GOSA, Belgrade, (in Serbian), (1997) 345-352.
M. Zrilić, M. Rakin, A. Sedmak, S. Sedmak, Experience in Fracture Mechanics Local Approach Application, Proceedings of the 6th International Scientific Conference on Achievements in the Mechanical Materials Engineering - AMME97, Miskolc, (1997) 71-75.
M. Zrilić, M. Rakin, A. Sedmak, S. Sedmak, Measurement Techniques in Local Approach to Fracture, Proceedings of the Fourth International Symposium on Measurement Technology and Inteligent Instruments, Miskolc, (1998) 358-361.
A. Sedmak, M. Rakin, Application of fracture mechanics in assessment of structural integrity, In: From Fracture Mechanics to Structural Integrity Assessment, (Ed. S. Sedmak, Z. Radaković), DIVK-TMF, (2004) 373-386.
M. Zrilić, M. Rakin, Z. Cvijovic, A. Sedmak, S. Sedmak, Structural integrity assessment by local approach to fracture, Proc. of 16th European Conference of Fracture ECF 16: Failure Analysis of Nano and Engineering Materials and Structures, Ed. E.E. Gdoutos, Alexandroupolis, Greece, (2006), published on CD by Springer.
M. Zrilic, M. Rakin, N. Gubeljak, M. Dobrojevic, N. Krunich, A. Sedmak, Ductile fracture modelling of advanced metallic materials. EMMC9 - MECAMAT, 9th European Congress on Mechanics of Materials, facilities of EDF "Les Renardières" Moret Sur Loing, France, (2006) 247-253.
B. Younise, M. Rakin, B. Medjo, N. Gubeljak, D. Kozak, A. Sedmak: Technical Gazette, 18 (2011) 333‐340.
B. Younise, M. Rakin, N. Gubeljak, B. Medjo, A. Sedmak: Struct Integrity Life, 11 (2011) 51‐56.
B. Younise, M. Rakin, N. Gubeljak, B. Međo, M. Burzić, M. Zrilić, A. Sedmak: Materials and Design, 37 (2012) 193-201.
B. Younise, M. Rakin, N. Gubeljak, B. Međo, A. Sedmak: Engineering Failure Analysis, 82 (2017) 435‐445.
M. Rakin, Z. Cvijovic, V. Grabulov, A. Sedmak: Polish Materials Science and Engineering, 22 (2001) 741-744.
M. Rakin, A. Sedmak, Z. Cvijović, M. Zrilić, S. Sedmak, Micromechanical approach - transferability of ductile fracture parameters, Proceeding of the 14th European Conference on Fracture - Vol III, EMAS Publishing, Krakow, (2002) 27-34.
T.L. Anderson: Fracture Mechanics, CRC Press, London, 1995.
J. Besson, D. Moinerau, D. Steglich, editors: Local approach to fracture, EUROMECH-MECAMAT, Mines, Paris, 2006.
A. Needleman, V. Tvergaard: International Journal of Fracture, 101 (200) 73-97.
Local Approach to Fracture, Edited by J. Besson, Les Presses de l'Ecole des Mines, Paris, 2004
B. Međo, M. Rakin, N. Gubeljak, M. Arsić, Z. Šarkočević, A.Sedmak, Failure resistance of drilling ring casting pipes with an axial crack. Engineering Failure Analysis 58 (2015) 429-440.
W. Musraty, B. Medjo, N. Gubeljak, A. Likeb, I. Cvijović-Alagić, A. Sedmak, M. Rakin: Engineering Fracture Mechanics, 175 (2017) 247-261.
W. Musraty, B. Medjo, N. Gubeljak, A. Stefane, P. Vejić, D., Sedmak, M. Rakin: Theoretical and Applied Fracture Mechanics, 103 (2019) 102302.
W. Musraty, B. Medjo, N. Gubeljak, A. Stefane, P. Vejić, D., Sedmak, M. Rakin: Procedia Strutural Integrity Theoretical and Applied Fracture Mechanics, 13 (2018) 1828-1833.
D. Damnjanovic, D. Kozak, I. Gelo, N. Gubeljak: Theoretical and Applied Fracture Mechanics, Vol. 103 (2019) 102286.
Zrilić M, Rakin M, Sedmak A, Aleksić R, Cvijović Z, Arsić M: Materials Science Forum, 518 (2006) 537-542.
M. Rakin, A. Sedmak, Z. Cvijović, M. Zrilić, S. Sedmak: Strength of Materials, 36 (2004) 33-36.
M. Zrilić, M. Rakin, A. Sedmak, S. Sedmak, Assessment of in-service degradation of steam pipeline steel by local approach method, Proceeding of the Conference: Life assessment and management for sructural components. Kiev, (200) 247-253.
M. Zrilić, M. Rakin, Lj. Milović, Z. Burzić, V. Grabulov: Metalurgija, 46 (2007) 87-92.
M. Dobrojević, M. Rakin, N. Gubeljak, I. Cvijovic, M. Zrilic, N. Krunich, A. Sedmak: Materials Science Forum, 555 (2007) 571-576.
M. Rakin, B. Međo, N. Gubeljak, A. Sedmak: Engineering Fracture Mechanics, 109 (2013) 221-235.
M. Rakin, Z. Cvijović, V. Grabulov, M. Zrilić, A. Sedmak, Determination of micromechanical ductile fracture parameters of pressure vessel steel, Proceeding of The 7th European Conference on Advanced Materials and Processes - Euromat, Published on CD, Rimini, 2001.
F. Mudry, M. Di Fant, A Round Robin on the Measurement of Local Criteria, Rapport Abrege N_ RE 93.319, IRSID, St. Germain, 1993.
W. Brocks, Numerical Round Robin on Micromechanical Models - Results, IWM-Bericht T 8/95, Fraunhofer Institut fuer Werkstoffmechanik (IWM), Freiburg, 1995.
European Structural Integrity Society, ESIS Publication P6-98: Procedure to measure and calculate material parameters for the local approach to fracture using notched tensile specimens, 1998.
European Structural Integrity Society, ESIS Publication - Draft P9-02D: Guidance on local approach of rupture of metallic materials, 2002.
G. Bernauer, W. Brocks, Numerical Round Robin on Micro-Mechanical Models - Results, ESIS TC8, GKSS Research Center, Geesthacht, 2000.
G Testa, N Bonora, D Gentile, A Carlucci, Y Madi: Procedia Structural Integrity, 3 (2017): 508-516.
Yang Li, Numerical Study on Ductile-to-Brittle Transition of Steel and its Behavior under Residual Stresses, Ph.D. thesis, NTNU, Trondheim, 2019.
M. Rakin, A. Sedmak, V. Grabulov, N. Gubeljak, Z. Cvijović, Determination of initial damage parameters in Gurson-Tvergaard-Needleman model, 9th International Conference on Mechanical Behaviour of Materials, Published on CD, Geneva, 2003.
Z.L. Zhang, C. Thaulow, J. Odegard: Engineering Fracture Mechanics, 67 (2000) 155-168.
J.R. Rice, D.M. Tracey: Journal of Mechanics and Physics of Solids, 17 (1969) 201-217.
V. Tvergaard, A. Needleman: Acta Metallurgica, 32 (1984) 157-169.
A.L. Gurson: Journal of Engineering Materials and Technology, 99 (1977) 2-15.
P.F. Thomason, Ductile Fracture of Metals, Pergamon Press, Oxford, 1990.
A. Sedmak: Fatigue Fract Eng Mater Struct, 41 (2018) 2438-2474.
F.M. Beremin, Experimental and numerical study of the different stages in ductile rupture: application to crack initiation and stable crack growth, In: Nemat-Nasser S., editor, Three-dimensional constitutive relations and ductile fracture, North-Holland Publ, (1981) 185-205.
Y. Huang, Accurate dilatation rates for spherical voids in triaxial stress fields. Trans ASME, 58 (1991) 1084-1086
R. Chaouadi, P. De Meester, W. Vandermeulen: International Journal of Fracture, 66 (1994) 155-164.
V. Tvergaard: International Journal of Fracture, 17 (1981) 389-407.
American Society for Testing and Materials, Standard practice for determining inclusion content of steel and other metals by automatic image analysis. ASTM Standard E 1245-89. Philadelphia, 1989.
C.C. Chu, A. Needleman: Journal of Engineering Materials and Technology, 102 (1980) 249-256.
B. Younise, Micromechanical fracture analysis of high strength steel weldments, D.Sc. thesis, University of Belgrade, 2013.
D.Z. Sun, R. Kienzler, B. Voss, W. Schmitt. Fracture mechanics twenty‐second symposium. In: Atluri SN, Newman JC, Raju I Jr, Epstein JS, eds. ASTM STP 1131, Vol.II, Philadelphia: American Society for Testing and Materials; (1992) 368‐378.
M.C. Burstow, L.C. Howard, R.A. Ainsworth: J Mech Phys Solids, 46(5) (1998) 845‐872.
C. Betegón, I. Peñuelas: Eng Fract Mech, 73(13) (2006)1865‐1877.
R. Jovičić, A. Sedmak, K. Čolić, M. Milošević, N. Mitrović: Chemicke listy, 105 (2011) 754-757.
N. Mitrovic, M. Milosevic, A. Sedmak, A. Petrovic, R. Prokic-Cvetkovic: FME Transactions, 39 (2011) 55-60.
N. Gubeljak: Structural Integrity and Life, Vol. 6, (2006) 65-74.
ASTM E1820-08.
Downloads
How to Cite
Issue
Section
License
Copyright (c) 2020 Aleksandar S Sedmak, Marko Rakin, Bojan Medjo, Bashir Younise
This work is licensed under a Creative Commons Attribution 4.0 International License.
Authors who publish with this journal agree to the following terms:
- Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgment of the work's authorship and initial publication in this journal.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgment of its initial publication in this journal.
- Authors are permitted and encouraged to post their published articles online (e.g., in institutional repositories or on their website, social networks like ResearchGate or Academia), as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).
Except where otherwise noted, the content on this site is licensed under a Creative Commons Attribution 4.0 International License.
According to the 